How To Install Blueskin Window Flashing

Posted on |

  • POST a QUESTION or COMMENT about how to buy & apply peel and stick flashing tape around window & doors or at housewrap joints or holes.

This helps direct water out away from window. In this type of installation, seal the cap flashing directly to the sheathing with high-quality sealant. Then place the top piece of flashing tape over the cap flashing and layer the house wrap over the tape. If you’ve added wooden trim around the window, the cap flashing goes over the wood trim. Product Description Blueskin ® VP100 Self-Adhered Water Resistive Air Barrier Membrane Picking up where traditional house wraps leave off, Blueskin ® VP100 offers a fully adhered solution that produces an air tight, water tight and weather tight membrane. This next generation vapor permeable air barrier picks up where traditional polymeric wraps leave off.

InspectAPedia tolerates no conflicts of interest. We have no relationship with advertisers, products, or services discussed at this website.


Peel and stick flashing tape or membrane questions & answers:

Frequently-asked questions and answers about how to buy, install & detail stick-on flashing tape around windows & doors.

This article series describes the selection and installation of peel-and-stick flashing membranes used on building exteriors to seal housewrap joints and to seal against air or water leaks around windows, doors, or other openings. Our photo at page top shows Typar® flashing tape installed above a new window. A better practice laps the housewrap over rather than under the stick-on flashing tape, a better detail but one omitted by many builders.

We also provide a MASTER INDEX to this topic, or you can try the page top or bottom SEARCH BOX as a quick way to find information you need.

Using Building Flashing Membranes - Peel & Stick Flashing Tape

Question: 'blue skin' for trailer roofs

(May 11, 2014) alex said:

can you put blue skin on a travel trailer roof and paint over with rubber paint

Reply:

Alex I'm not sure what the blue skin product is (name and product name would allow some research. But certainly there are a number of roof-over materials for leaky trailer roofs, including rubber coatings. Without a membrane these may not be a lasting repair.

What I would not try is simply rolling out a self-adhering flashing membrane on your trailer's roof - don't use a product that was not designed to be left exposed to the weather. It won't endure.

Question: flashing membranes adherence to old masonry chimneys

(July 28, 2014) Jean said:

Can peel and stick flashing membranes be used on masonry (old chimney) or only on wood decking?

Reply:

Install

Jean,

Some of the flashing membrane product lines listed above such as FortiFlash® include products designed to adhere to cleand dry masonry.

Unfortuntately, too-often I have not seen good adhesion of a peel-and-stick flashing membrane along a masonry surface such as an older, rough-surfaced masonry brick or block chimney. And these membranes are not intended to be left exposed to the weather. Further, even if it adhered, you'd need counterflashing over the upper edge of the membrane to assure a durable installation.

Question: peel-and-stick membranes in roof valleys

(Aug 12, 2014) Donald said:

Can peal and stick membranes be used on steel roof valleys?

Reply:

Donald, the flashing tapes we describe here are expected to be covered by a finish material. These membranes do add valuable leak-insurance used beneath a finsish-material placed in a roof valley.

Question: will flashing tapes seal around a screw

(Aug 31, 2014) Gary said:

Will Flashing Tapes and membranes self seal around a screw, particularly the screw that holds the exterior finish (i.e. Siding) on to the substrate?

Reply:

Gary

Great question. My answer is yes ... and sometimes no.

Peel-and-stick membranes are intended to seal around small-diameter penetrants such as staples and roofing nails. Where I've seen leaks through a P&S membrane on a roof they were traced to a mis-hammered roofing nail that folded over and whose head made a significant cut in the membrane.

I've also come across a few tears in flashing membranes that were subjected to twisting forces from a screw as it penetrated the material, in particular if the flashing material was not itself thoroughly bonded to the substrate surface.

Where I've seen leaks over doors and windows that were traced to flashing tape troubles the issue was either failure of the tape to bond to an older weathered surface or to someone having driven a 16d nail through the material.

And of course no flashing tape on a building wall, say over a window, is going to be able to prevent leaks that run down behind the housewrap from some leak point higher on the building.

Question: Blueskin SA compatable for a tie-in with a 2-ply hot asphalt vapour retarder

(Sept 3, 2014) Leo said:

Is Blueskin SA compatable for a tie-in with a 2-ply hot asphalt vapour retarder on a flat roof transition?

Reply:

Blueskin SA is an SBS-modified self-adhering membrane made of SBS rubberized asphalt compound that has been laminated onto a blue polyethylene reinforcing film.

Blueskin is produced by the Henry Company, 999 North Sepulveda Blvd., Suite 800 El Segundo, CA 90245 310-955-9200. Contact the company at E-mail: productsupport@henry.com Phone: 800-486-1278

The material is designed to bond or 'stick to' prepared concrete, concrete block, primed steeol, mill-finished aluminum (remove any oils), anodized aluminum, galvanized metal, gypsum board and plywood.

The material (as well as others of this type) is not designed to bond to a hot asphalt-sealed surface.

Question:

(Oct 7, 2014) Anonymous said:

We will be pouring a large 70' patio with stamped concrete. What type of flashing should be used when connecting new concrete landings to the house wood frame support? The landings are both 12' wide where they connect to the house and will allow entry into two 8 foot wide doorwalls.

Reply:

Please take a look at DECK FLASHING

Question: how to remove flashing membranes from concrete

11/06/2014 Steve said:

I bet this isn't asked often. Once you apply Fortiflash to concrete, how do you get the stuff off. We removed an old shed that was sealed to the concrete driveway with this stuff, and outside of grinding it off, we haven't had any luck.

Reply:

Steve,

Removing a well-adhered flashing membrane such as FortiFlash can be difficult on any surface. At least on concrete you could heat it gently to try peeling it off but I'd bet that the result will leave black residue on the concrete surface.

For other readers, FortiFlash(R) is a waterproof flashing membrane produced by Fortifiber Building Systems Group (R), a Fernley NV USA company. The product is a self-adhesive membrane reinforced by high-density polyethylene film that the manufacturer also refers to as “rubberized asphalt” and is described more technically as “a self-sealing SBS modified asphalt core laminated to a cross-laminated high-density polyethylene film reinforcement with a siliconized paper release sheet.”

It’s possible that the installer used Fortiflash 40(r) for floors - a vapor retarder system that can be adhered to concrete. It looks as if the composition of that product is similar.

As such if you can physically peel off the reinforced sheet you might use an organic solvent on the remaining modified asphalt adhesive. The company’s literature points out that the product is not compatible with EPDM (Rubber roofing), flexible PVC products and some sealants - but I don’t find much help from those products when considering how to remove FortiFlash membranes.

My best advice would is to contact the company directly for advice on the safest and most effective solvent to use.

Contact Fortifiber Building Systems at

1-800-773-4777 for sales and technical assistance. Website: www.fortifiber.com

Question: how to remove peel and stick flashing tape or membranes

(Nov 6, 2014) Steve said:
I bet this isn't asked often. Once you apply fortiflash to concrete, how do you get the stuff off. We removed an old shed that was sealed to the concrete driveway with this stuff, and outside of grinding it off, we haven't had any luck.

Reply:

Steve,

Removing a well-adhered flashing membrane such as FortiFlash can be difficult on any surface. At least on concrete you could heat it gently to try peeling it off but I'd bet that the result will leave black residue on the concrete surface.

How To Install Blueskin Window Flashing Installation

For other readers, FortiFlash(R) is a waterproof flashing membrane produced by Fortifiber Building Systems Group (R), a Fernley NV USA company. The product is a self-adhesive membrane reinforced by high-density polyethylene film that the manufacturer also refers to as “rubberized asphalt” and is described more technically as “a self-sealing SBS modified asphalt core laminated to a cross-laminated high-density polyethylene film reinforcement with a siliconized paper release sheet.”

How To Install Blueskin Window Flashing Screen

It’s possible that the installer used Fortiflash 40(r) for floors - a vapor retarder system that can be adhered to concrete. It looks as if the composition of that product is similar.

As such if you can physically peel off the reinforced sheet you might use an organic solvent on the remaining modified asphalt adhesive. The company’s literature points out that the product is not compatible with EPDM (Rubber roofing), flexible PVC products and some sealants - but I don’t find much help from those products when considering how to remove FortiFlash membranes.

My best advice would is to contact the company directly for advice on the safest and most effective solvent to use.

Contact Fortifiber Building Systems at

1-800-773-4777 for sales and technical assistance. Website: www.fortifiber.com

Question: builder left out flashing membrane now I have a leak

How to install blueskin window flashing caulking

(Nov 7, 2014) Steve K. said:
I have an leak that is giving me an immense headache. My builder talked me into creating a storage room under my front porch. Because the porch large exposed to the weather, I instructed him to install a waterproof membrane under the concrete slab and to lap it under the Tyvek membrane on the house's exterior.

He forgot that detail, and I did not discover the mistake until the house was completed. The porch is poured concrete over a metal pan. The exterior structure consisted of OSB (all seams taped), one inch of Dow blue foam (all seams taped), Commercial D housewrap, 1x4 pressure treated strapping, and then cement siding.

When it rains, the most exposed portion of the porch leaks into the storm room, wetting the framing and introducing water into my very tight house. (The builder is MIA at this point.) I looked around for solutions but not found one. Taking off some of the siding, cutting back to the sheathing, and installing some flashing over the OSB and concrete seems like the best option, but I am not knowledgeable enough about building materials to know for sure.

How To Install Blueskin Window Flashing

Reply:

Steve

I am not sure I've got the details clearly in mind for the case you describe. Use our CONTACT link found at page top or bottom to send me photos and a sketch if you can and I might make more sense of this leak problem.

I'm a bit worried that flashing that terminates under ground and runs up under building siding risks giving an attractive pathway for termites (if you've got those critters in your area)

And I'm unclear on how the storage room is open to or protected from the weather.

So pending a better understanding I can just offer a very general comment that flashing is expected both to keep water out of a construction intersection of planes and to direct water out onto an exposed surface where it can drain away without causing trouble.

Question:

(July 30, 2015) daren said:
if i was to use this tape in conjunction with liquid rubber, how would the rubber adhere to the tape?
would it be better to rubber the seam and the apply tape...followed by rubber

Reply:

That's not an application I've seen described by the flashing tape manufacturer. I am doubtful that liquid rubber or any other adhesive will bond well to what I think is a super-smooth polyethylene type or mylar type covering left on the exposed side of the flashing tape. It might adhere to a metallic covering used on some tapes.

Question: is it wrong to use flashing tape underneath a window or door

Pat said:
Can someone please clarify this issue? Most everywhere I've read about window flashing tape, it states to never apply it to the bottom of the window on the outside so water can exit to the house wrap instead of under the house wrap.

My siding crew taped the bottom of the window like shown in this article but I'm less worried about it because there's an open flap of house wrap below the window where water can eventually exit. Also, I insisted on a rain screen and the house wrap should let water escape so it should get stuck inside. Either way, I don't think taping the bottom is hardly ever recommended.

Reply: no but it must be installed before the window or door is set in place.

Pat: You're quite correct. The photo showing peel and stick flashing tape applied over the window bottom flange and onto the building WRP or housewrap is not a recommended detail and might trap water in the window rough opening. Please see complete details at WINDOW & DOOR FLASHING TAPE DETAILS - separate article

What is the best way to flash around windows & doors and how should flashing tape be used at these openings? This article series shows best practices, common practices, and some not-so-good practices using peel-and stick flashing tape around windows, doors, and other building wall penetrations.

Article Series Contents

  • PEEL & STICK FLASHING MEMBRANES
    • WINDOW & DOOR FLASHING TAPE DETAILS - separate article

...

Continue reading at PEEL & STICK FLASHING MEMBRANES - topic home, or select a topic from the closely-related articles below, or see the complete ARTICLE INDEX.

Suggested citation for this web page

FLASHING MEMBRANE FAQs at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.

INDEX to RELATED ARTICLES: ARTICLE INDEX to BUILDING FLASHING

Or use the SEARCH BOX found below to Ask a Question or Search InspectApedia


...

Ask a Question or Search InspectApedia

Try the search box just below, or if you prefer, post a question or comment in the Comments box below and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment below may be delayed:if your comment contains an image, web link, or text that looks to the software as if it might be a web link, your posting will appear after it has been approved by a moderator. Apologies for the delay.

Comment Form is loading comments...

Technical Reviewers & References

  • Best Practices Guide to Residential Construction, by Steven Bliss. John Wiley & Sons, 2006. ISBN-10: 0471648361, ISBN-13: 978-0471648369, Hardcover: 320 pages, available from Amazon.com and also Wiley.com. See our book review of this publication.
  • Eric Galow, Galow Homes, Lagrangeville, NY. Mr. Galow can be reached by email: ericgalow@gmail.com or by telephone: 914-474-6613. Mr. Galow specializes in residential construction including both new homes and repairs, renovations, and additions.
  • Paul Galow [Website galowconsulting.com ] - technical consultant on networking, LAN design, applications support. Galow Consulting Services [Website galowconsulting.com ] , 914-204-1749, email: paulgalow@galowconsulting.com
  • John Rudy, Advantage Home Inspections, Flemington N.J. 08822 home inspector, 908-806- 6364, Home, Radon & Termite Inspections, Central & Parts of North New Jersey, email: jonadvantage1@yahoo.com

Books & Articles on Building & Environmental Inspection, Testing, Diagnosis, & Repair

  • Our recommended books about building & mechanical systems design, inspection, problem diagnosis, and repair, and about indoor environment and IAQ testing, diagnosis, and cleanup are at the InspectAPedia Bookstore. Also see our Book Reviews - InspectAPedia.
  • Decks and Porches, the JLC Guide to, Best Practices for Outdoor Spaces, Steve Bliss (Editor), The Journal of Light Construction, Williston VT, 2010 ISBN 10: 1-928580-42-4, ISBN 13: 978-1-928580-42-3, available from Amazon.com
  • The Journal of Light Construction has generously given reprint permission to InspectAPedia.com for this article. All rights and contents are ©Journal of Light Construction and may not be reproduced in any form.
  • ...

How To Install Blueskin Window Flashing Detail

  • Carson, Dunlop & Associates Ltd., 120 Carlton Street Suite 407, Toronto ON M5A 4K2. Tel: (416) 964-9415 1-800-268-7070 Email: info@carsondunlop.com. The firm provides professional HOME INSPECTION SERVICES and also extensive HOME INSPECTION EDUCATION and home inspection-related PUBLICATIONS. Alan Carson is a past president of ASHI, the American Society of Home Inspectors.
    Thanks to Alan Carson and Bob Dunlop, for permission for InspectAPedia to use text excerpts from The Home Reference Book & illustrations from The Illustrated Home. Carson Dunlop Associates' provides extensive home inspection education and report writing material.
    The ILLUSTRATED HOME illustrates construction details and building components, a reference for owners & inspectors.
    Special Offer: For a 5% discount on any number of copies of the Illustrated Home purchased as a single order Enter INSPECTAILL in the order payment page 'Promo/Redemption' space.
    TECHNICAL REFERENCE GUIDE to manufacturer's model and serial number information for heating and cooling equipment, useful for determining the age of heating boilers, furnaces, water heaters is provided by Carson Dunlop Weldon & Associates
    Special Offer: Carson Dunlop Associates offers InspectAPedia readers in the U.S.A. a 5% discount on any number of copies of the Technical Reference Guide purchased as a single order. Just enter INSPECTATRG in the order payment page 'Promo/Redemption' space.
  • The HOME REFERENCE BOOK - the Encyclopedia of Homes, Carson Dunlop & Associates, Toronto, Ontario, 25th Ed., 2012, is a bound volume of more than 450 illustrated pages that assist home inspectors and home owners in the inspection and detection of problems on buildings. The text is intended as a reference guide to help building owners operate and maintain their home effectively. Field inspection worksheets are included at the back of the volume.
    Special Offer    : For a 10% discount on any number of copies of the Home Reference Book purchased as a single order. Enter INSPECTAHRB in the order payment page 'Promo/Redemption' space. InspectAPedia.com editor Daniel Friedman is a contributing author.
    Or choose the The HOME REFERENCE eBook for PCs, Macs, Kindle, iPad, iPhone, or Android Smart Phones.
    Special Offer    : For a 5% discount on any number of copies of the Home Reference eBook purchased as a single order. Enter INSPECTAEHRB in the order payment page 'Promo/Redemption' space.
  • Building inspection education & report writing systems from Carson, Dunlop & Associates Ltd
    COMMERCIAL BUILDING INSPECTION COURSES - protocol ASTM Standard E 2018-08 for Property Condition Assessments
    HOME INSPECTION EDUCATION COURESES (Canada)
    HOME INSPECTION EDUCATION COURSES (USA) including home study & live classes at eleven colleges & universities.
    HOME INSPECTION EDUCATION: HOME STUDY COURSES - ASHI@Home Training 10-course program.
    Special Offer: Carson Dunlop Associates offers InspectAPedia readers in the U.S.A. a 5% discount on these courses: Enter INSPECTAHITP in the order payment page 'Promo/Redemption' space. InspectAPedia.com editor Daniel Friedman is a contributing author.
  • The Horizon Software System manages business operations,scheduling, & inspection report writing using Carson Dunlop's knowledge base & color images. The Horizon system runs on always-available cloud-based software for office computers, laptops, tablets, iPad, Android, & other smartphones

How To Install Blueskin Window Flashing Panel

Publisher InspectApedia.com - Daniel Friedman